PVC-Steel Pipe Saddles/Sleeves

Water Works Tools PVC and Steel Pipe Saddles are designed specifically for steel and pvc mains and can be used on domestic water, heating hot water, Air, natural gas, glycol and sewage mains. All saddles have a stainless steel IP male thread for easy installation of you full port ball valve. Please specify main size and outlet size when ordering. If you have any questions about these tapping saddles please call and we can help you pick the correct saddle for your needs.

Panel: Type 304 (18-8) Stainless steel per ASTM A240
• Gasket: Nitrile (Buna-N, NBR) Chek-O-Seal with multi o-ring sealing ribs from 100% new rubber to ensure performance
under varying pressures with superior storage characteristics. Suitable for oils, acids, alkalines, most Hydrocarbon
Fluids (aliphatic), portable water, and other chemicals within temperature range of –40o F - +180o F.
• Lugs: Type 304 (18-8) Stainless steel per ASTM A240.
• Bolts and Nuts: Type 304 (18-8) Stainless steel per ASTM A193 & A194.
• Note: Hex nuts are furnished with fusion bonded coating to prevent seizing and galling.
• Outlet: Type 304 (18-8) Stainless steel per ASTM A276
• All outlets are "Male Threaded NPT" Working Pressure: Maximum 150 PSI.

PDF Saddle Installation Guide

 PVC-Steel Pipe Saddles/Sleeves

Pipe Size in.

IPS O.D. in.

Nipple Size in.

Price

In Stock
3/4 1.05 3/4 $165.00 Yes
1 1.32 3/4 $198.00 Yes
1 1.32 1 $198.00 Yes
1-1/4 1.66 3/4 170.50 Yes
1-1/4 1.66 1 $203.50 Yes
1-1/4 1.66 1-1/4 $203.50 Yes
1-1/2 1.90 3/4 $176.00 Yes
1-1/2 1.90 1 $236.50 Yes
1-1/2 1.90 1-1/4 $231.00 Yes
1-1/2 1.90 1-1/2 $236.50 Yes

Pipe Size in.

IPS O.D. in.

Nipple Size in.

Price

In Stock
2 2.38 3/4 $198.00 Yes
2 2.38 1 $203.50 Yes
2 2.38 1-1/4 $236.50 Yes
2 2.38 1-1/2 $242.00 Yes
2 2.38 2 $236.50 Yes
2-1/2 2.88 3/4 $187.00 Yes
2-1/2 2.88 1 $209.00 Yes
2-1/2 2.88 1-1/4 $269.50 Yes
2-1/2 2.88 1-1/2 $269.50 Yes
2-1/2 2.88 2 $324.50 Yes

Pipe Size in.

IPS O.D. in.

Nipple Size in.

Price

In Stock
2-1/2 2.88 2-1/2 $379.50 Yes
3 3.50 3/4 $176.00 Yes
3 3.50 1 $220.00 Yes
3 3.50 1-1/4 $231.00 Yes
3 3.50 1-1/2 $236.50 Yes
 
 3 3.50 2 $236.50 Yes
 
 3 3.50 2-1/2 $269.50 Yes
 
 3 3.50 3 $286.00 Yes
 
 4 4.50 3/4 $198.00 Yes
 
 4 4.50 1 $209.00 Yes

Pipe Size in.

IPS O.D. in.

Nipple Size in.

Price

In Stock
4 4.50 1-1/4 $220.00 Yes
4 4.50 1-1/2 $231.00 Yes
4 4.50 2 $231.00 Yes
4 4.50 2-1/2 $269.50 Yes
4 4.50 3 $269.50 Yes
4 4.50 4 $324.50 Yes
4 x 12 4.50 4 $324.50 Call
5 5.56 1 $192.50 Yes
5 5.56 1-1/4 $192.50 Call
5 5.56 1-1/2 $192.50 Yes

Pipe Size in.

IPS O.D. in.

Nipple Size in.

Price

In Stock
5 5.56 2 $203.50 Yes
5 5.56 3 $209.00 Yes
6 6.63 3/4 $203.50 Yes
6 6.63 1 $203.50 Yes
6 6.63 1-1/2 $214.50 Yes
6 6.63 2 $231.00 Yes
6 6.63 2-1/2 $280.50 Yes
6 6.63 3 $280.50 Yes
6 6.63 4 $346.50 Yes
6 x 12 6.63 4 $363.00 Call

Pipe Size in.

IPS O.D. in.

Nipple Size in.

Price

In Stock
8 8.63 3/4 $220.00 Yes
8 8.63 1 $231.00 Yes
8 8.63 1-1/2 $253.00 Yes
8 8.63 2 $253.00 Yes
8 8.63 2-1/2 $291.50 Yes
8 8.63 3 $324.50 Yes
8 8.63 4 $346.50 Yes
8 x 12 8.63 4 $368.50 Yes

INSTALLATION INSTRUCTIONS FOR WATER WORKS TOOLS COPPER SADDLES

1. Thoroughly clean the pipe surface, and inspect the area where the saddle will be installed for flaws, gouges,
protrusions, excessive corrosion, etc. irregular surfaces should be avoided to assure maximum gasket sealing.
2. Lubricate the pipe and gaskets with a light soap/water solution and center the outlet of the saddle over the
desired area and continue around the pipe with the saddle.
3. Install washers, bars, flat Teflon washers and nuts. Evenly tighten the nuts and maintain and even gap
between the ends of the panel.
4. Tighten nuts evenly, alternating from one to the other always maintaining an even gap distance between both
panels. Tighten nuts in this sequence until tight. Do not over tighten. Wait 10-15 minutes to allow the gaskets to
fully compress. Recommended torque is 35-40 ft lbs.
5. Retighten nuts in sequence following step 4.
6. On Hot Water Lines, especially over 1300 -1400 F allow the gaskets to fully compress, and recheck the nut’s
tightness after 60-90 minutes. (After adding insulation, the heat to the gasket can increase, causing additional gasket compression.)

order now.

Hottap Machines

Hottap machines

Most durable tapping machines on the market These tapping machines offer lifetime phone support so that when you purchase your machine you have the support needed to succeed in your tapping business. Please call us for supports...

 
Learn more

Pilot Drill Bits

Pilot Drill Bits with Retention Wire

Our pilot drill bits will catch your coupon. All you have to do is order our drill bits and we will provide the support on all your pilot drill bit accessories.

 
Learn more

Follow us:


 

Support call Water Works Tools.com

Contact Us.

Our company is built around the belief of suppying the correct tools and support needed for your company to be able to perform your job and be successful in all of your hot tap, linestopping and pipefreezing needs. Call today and we will be happy to help you get started in choosing the correct tools for you job. 951-233-5574

Contact us

Copper Saddles

Copper Pipe Saddles

Tapping saddles delivered to your jobsite so you can perform critical hot taps or linestops. We offer hot tap saddles for copper, steel, pvc, ductile iron, cmlc and many other pipelines. Call today or email and we can help guide you through the process of picking the correct hot tap or line stop saddle to meet your needs the first time!

Learn more
 

Copyright © 2011 www.Hottap-Machine.com - All Rights Reserved - Please see our Privacy Policy if needed or add your website to our Directory

Designed by www.WaterWorksTools.com